Table of Contents
Why won’t my Porter-Cable nail gun fire nails?
The most frequent reason for a nailer not firing is jams. Thankfully, they are frequently simple to remove. Retract the feeder mechanism, empty the magazine of any extra fasteners, and then disconnect the tool from the air supply to ensure safety. Depending on the type of nailer you have, you can then attempt to clear the jam. Possible reasons why a nail gun won’t fire nails If your nail gun won’t fire nails, the first possible cause is that the air pressure isn’t set high enough. The nail feed being obstructed by something is the second potential problem. The third potential problem is using the wrong nails with the gun.
Replace the trigger valve if it is double firing while the gun is set to bump fire. Leaky O rings on the trigger valve can result in this if the nailer is configured to trigger fire.
A nail jam is preventing the nails from moving forward, which is one potential reason why a Paslode nail gun won’t fire. The gas fuel cell is either empty, out of date, or improperly attached. There are the wrong kind of Paslode nails being used.
Take the nailer apart and check each component for wear or damage, or take it to a shop. Air Leaks Out Back While this is a good indication that seals need to be reseated through dry firing or bumping the gun, it’s also possible that air is escaping from the back of the tool as a result of a broken component.
Batteries, electricity, fuel, air, or any of these sources can power nail guns. You must understand how the nail gun receives power before you purchase one. Because of its affordable price and powerful output, most people opt for air-powered nail guns. An air compressor, however, is necessary for air-powered tools.
Why won’t the piston on my nail gun work again?
You should try lubricating the tool as soon as possible if your driver does not show up. Through the air inlet, add 5 to 6 drops of air tool oil. To get the lube to circulate throughout the tool, connect the air line and fire the gun a few times. Start troubleshooting the components if this doesn’t fix the issue. Check your nailer’s o-rings, bumper, seals, driver, piston ring, springs, piston head valve, trigger valve, air tool oil, and gasket if the driver won’t return. The following repair advice will help you through your own DIY repair once you’ve identified the problematic component.
How come my nail gun only fires air?
If you try to use a pneumatic nail gun or stapler but all you hear is air leaking when you pull the trigger, your tool’s O-Ring probably isn’t sealing properly. Since the valve is likely sealed when the trigger is not pulled, you might not hear air leaking. Simply pulling the trigger on any nail gun, hoseless or not, won’t launch steel spikes into the air. You must press a gun’s nose firmly against a hard surface in order to release the safety before it can fire.
To keep your nail gun functioning properly, lubrication will be required. Make sure to only use lubricant designed for use with pneumatic tools. Other lubrication could make the tools’ o-rings swell or might be too thick to use.
The hammer may not feed the nails into the line if they are not properly loaded. You’ll end up striking the wood with the hammer alone rather than a nail.
Never disable the safety mechanisms on a nail gun. This is absolutely forbidden. When holding or carrying a nail gun, remind your employees to keep their fingers away from the trigger. Never drag the nail gun by the hose or lower it from above.
What types of nails can be used in a Porter-Cable finish nailer?
There are 2500 16-gauge finish nails in each box. Its point is chiseled. To reduce reloading, 50 fasteners are included in each stick. Any 16-gauge finish nailer with a 2 in. Porter-Cable FN model nailer are compatible with this nail. Small compressors with a one-gallon capacity and 2 points CFM can be used with pin nailers. Brad nailer: A small compressor can effectively power these nail guns with a two-gallon tank and 20 CFM. Finish nailer: Finish nailers perform best when used with a compressor that has a two to three gallon tank and two CFM.
And that’s precisely what this American-made CRAFTSMAN CMEC6150K air compressor has to offer, with a maximum pressure of 150 PSI and airflow rates of 2. SCFM at 90 PSI, which are more than enough to power even the most airflow-hungry framing nailer.
A: Until the pressure in your air bottle drops below 55 or 60 psi, you can use an air bottle to power your nail gun. How much pressure is necessary to drive the nails will depend on the type of material you are using. Between the bottle and the nailgun, a regulator is still required.
CAUTION: Only use Porter-Cable brad nails that have been approved (see the list of ACCES- SORIES in the back of this manual). This device is made to work with compressed air that is clean, dry, and pressured to a set range between 70 and 120 PSI (Pounds per sq. Inch).
What nail gun pressure setting should I use for Porter-Cable?
We pair our dependable, long-lasting Brad Nailer with a 150 psi. To drive more nails than you could with a conventional 135 max psi, use a max pressure compressor. The minimum recommended operating pressure (PSI) for most nailers is between 70 and 120.
The majority of air tools require 70 to 90 PSI. Any light- to medium-duty air compressor can manage 90 PSI with ease, but you should always have the compressor provide more flow than is required. Observe the PSI rating at all times. The tool won’t work properly if you don’t provide enough air volume.
Utilizing this dial, it’s simple to adjust the pressure to the type of material you’re nailing. For the perfect pressure, it might take a few test nails in a scrap of wood. The pressure dial and the depth of drive knob both allow you to control how deeply you drive the nail into the wood.
Is oil required for Porter-Cable nails?
Any good quality, 10 weight, non-detergent oil approved for use in pneumatic tools is acceptable, though Porter-Cable accessory item PTA1 is preferred. The majority of home centers and other retailers who sell pneumatic nailers ought to have a suitable oil on hand. Traditional Oiled Nail Guns To keep them operating properly, oiled nailers need to be lubricated on a regular basis. Every time you use the tool, add a few drops of oil to the air inlet to reduce heat and friction and stop valves, seals, and O-rings from wearing out. You should oil the tool more frequently when it is in heavy use.
Never use motor oil, transmission fluid, WD-40, or aerosol lubricants. Since most pneumatic nail guns have rubber o-rings, many generic lubricants will eventually eat through rubber, doing more long-term harm than good.
Nail guns can be hazardous if used improperly because they can be powered by electricity, compressed air, or combustible gas. To use a nail gun safely and effectively if you’re unfamiliar with this kind of tool, keep reading.
Traditional Oiled Nail Guns Oiled nailers need to be lubricated on a regular basis to keep them operating properly. Every time you use the tool, put a few drops of oil into the air inlet to reduce heat and friction and stop valves, seals, and O-rings from wearing out. You should oil the tool more frequently when it is in heavy use.